Sunday, March 3, 2013

Motor Mount 2.0

An alternate design being considered would incorporate "BMW style" motor mounts that would be bolted directly to the sides of a "clam shell" that encircles the body of the Warp 11.  This design would use the same foundry casting for the left and right side motor mounts.  The top and bottom castings of the "clam shell" , also identical, would provide an 11.45 inch opening when bolted together.  A differently sized  "clam shell" casting with a 9.25 inch nominal opening would allow for the substitution of a Warp 9 onto the same motor mounts. 

Mounting flanges at the equator of the Warp 11 "clam shell" would mate to integral flanges on the face of each "BMW style" mounting bracket.  To demonstrate the design, the previously sectioned BMW left side mounts were further sectioned (picture DSC05438) to allow room for the two mounting plates.  The sectioned BMW mounts are neither symmetrical or in good alignment when mounted, but they allow for a good visualization of a possible design. 



Picture DSC05438:  View of the final BMW left side motor mount (top casting in picture) after the final sectioning with a hand held band saw.  The additional removal of metal provides space for a flange to be welded to the side of the "clam shell" as well as a second flange to be welded to the mounting bracket.


Picture DSC05452:  Top view of the prototype installed on the top surface of the Warp 11.  Note the asymmetry at the mounting brackets.  The angle of the picture does not demonstrate the fact that both pairs of flanges are parallel to each other and equidistant to sides of the Warp 11 motor.

 


Picture DSC05451:  Anterior view of the top half of the four piece design.  Wood wedges were inserted to correct for a slight misalignment.  The wedges will be glued in place, and new dimensions confirmed on the workbench after the assembled framework is removed from the car.




Picture DSC05454:  Close up view of the left side mounting flanges.  The top and bottom halves of the "clam shell" will be joined together with a pair of vertical threaded rods or bolts (not shown).  A rubber trim element will be glued to the inner contact surfaces of the "clam shell" to provide for a snug fit and to reduce any vibration noise.  

Fabrication:

The design was initially drawn on 3/16 inch plywood and cut out with a table top band saw.  The outline of the design was then traced onto prototyping foam (McMaster Carr, part 3152T41).  The foam pattern was cut out and the two plywood pieces then glued to opposite sides of the foam spacer.  Two sets of temporary nuts and bolts were added to provide strength while the glue was setting and the sides sanded.  Four 4" by 4" plywood "flanges" were cut out with two of them being hot glued to the sectioned BMW mounting brackets.  During the trial fitting it was found that the alignment of the flanges on the "clam shell" was not correct, and wooden shims were required to correct the alignment.  The wooden flange on the "clam shell"(including the shims) were then glued in place so that upon removal from the car, the final dimensions would be maintained and measured on the workbench.

In the final design, both pairs of flanges would be parallel to each other and perpendicular to the horizontal plane of the car.  The foam core adjacent to the motor body was recessed to allow for clearance of the red painted bolt heads (two of which are visible in picture DSC05454).  These bolt heads are part of the Warp 11 motor.  The top surface of the "clam shell" is flat, parallel to the floor, and wide enough to assist in the mounting of a controller.  The merit of this design is that only two different castings are required for the project.  The top and bottom of the clam shell are the same casting, and both the left side and the right side mounting supports are the same casting.  A differently sized "clam shell" casting would allow for the use of other Warp style motors without changing the mounting brackets.

Friday, March 1, 2013

Motor Mount 1.2

The initial design, based upon the measurements described in the previous blog entry (dated 2/14/2013, Part 1), was constructed using 3/16 inch plywood, 1" thick wood blocks, and nuts, washers, and bolts.  The final finished product would be fabricated using plate steel and a good welder. 

The concept is to have a metal arch that rests directly on both BMW motor mounts.  By using three nuts, four washers, and a fully threaded bolt, it was possible to rigidly hold the two wooden arches parallel to each other during trial assembly and fitting.  The final design would include a metal band bent with a radius of about 5.725 inches (11.45 inches is the outer diameter of the Warp 11).  The base of each arch would be welded to the curved band.   Strategically drilled bolt holes in the curved base band would allow for the insertion of bolts directly into the motor housing.  These bolts would help prevent torque induced rotation within the motor mount while under full load.


Picture DSC05424:  View of the assembled wooden model of a mounting harness for the Warp 11.   The blocks of wood at 3:00 and 9:00 have not yet been trimmed to match the contour of the lower arch.


Picture DSC05423:   Anterior view showing the top half of the wooden prototype positioned for a trial fitting.



Picture DSC05420:  Top view of the top half of the wooden prototype.

This design requires that the arches be cut from steel plate, a curved base plate formed, and final welding all three pieces together.  The final height required to provide adequate strength of the arch (and the depth of the arch below the motor) has not yet been determined.  If the top of the arch were made flat, then the surface could be used as a mounting point for other components.  This design is simpler, but less universal, when compared to attempting to incorporate a modified BMW style left side motor mount as was previously described.   

Thursday, February 14, 2013

Motor Mount Adapter 1.0

 
Taking measurements within the motor compartment presents quite a challenge.  It is difficult to measure between the studs and the sides of the motor, the vertical aspect, etc.  The following method was decided upon, with full understanding that although the measurements will not be exact, that they should be sufficiently close to achieve the required result.

Part 1:
 
Sooooo, having said that, the Warp 11 was initially positioned as close to center (between the two motor mount stud bolts) as could be measured.   The focus was more upon having an identical distance from the center of each stud to the side of the motor, than having the exact measurement itself.  Both dimensions were adjusted until they were eventually different by less than 1 mm.  The base of the motor was previously shimmed with wooden wedges to elevate it off the frame and position it vertically.  The actual vertical height above the frame (and relative to the engine mounts) will be reported later once there is greater confidence  in the measurement.
 
The way the measurements were determined was as follows.  A 30”x24”x 0.125” cardboard sheet was first measured to mark the mid line, allowance was made for a minimum space of 1" at the top of the cardboard (for a future cross brace).  The outline of the 11.45" outer diameter of the Warp 11 motor was centered, outlined, and cut out.  The drawing was then cut in half, so that the bottom edge of the cardboard would essentially be at the height of contour (ie., the "equator" of the Warp).  The final dimension of the top cardboard piece (which only has half of the Warp outline) was 10.625" tall x 24" wide.  This allowed the cardboard template to drop snugly onto the top of the Warp 11 motor.  The centers of two smaller square pieces of cardboard were then marked so that they could be aligned very closely with the centers of the M10 studs that protruded from the rubber engine mounts.  The edges of the cardboard squares were exactly flush with the metal landing areas of the engine mounts.  When all three pieces of cardboard were stable and in direct contact, 1.875" wide Scotch tape was carefully applied to bind all of the pieces together.

 
 Picture DSC05406 showing the cardboard template positioned on the Warp 11 and the cardboard "feet" resting on the motor mounts. All three pieces were then taped carefully together.
 
 
The entire cardboard jig was then pulled directly out of the motor compartment and laid on a fresh 20" x 30" cardboard sheet.  The relationship of the bottom edges of the small cardboard were then transferred to the new cardboard and a full scale drawing made to show the final relationships of the Warp 11 and the mounting pads.
 
 
Picture DSC05404 showing the cardboard "template" positioned on a fresh cardboard for transfer of the critical dimensions.
 
This process did not require that the car be level, nor did it matter if the 12"x24" cardboard piece was level to either the floor or to the plane of the car.  As it turned out, after drawing a horizontal line that connected the midpoint of the base of each mounting stud, and extending the lines that represented the landing area of  the mounting pads, the extended landing area lines joined at almost exactly the mid line, and at 150 degrees relative to each other !!  Thus, the motor mounts are each -15 degrees relative to horizontal !!!
 
Measured Approximate Dimensions of 1992 BMW 325i motor mounts:
 
Distance from center to center of studs (of engine mounts): 23.8125 inches
Angle of landing pads of engine mount relative to the horizontal plane: -15 degrees.
(Both motor mounts angle downward toward the mid line of the car.)
Height of the M10 studs embedded in the hard rubber mounts: 1.0625 inches
Approximate diameter of the metal landing area that is cast into the rubber engine mount: 1.75 inches.

Part 2:
 
It appeared that the BMW driver side motor mount (it arches over the steering column) might provide some useful dimensional information.  Two new units were purchased directly from Patrick BMW (in stock and $38 each) and then with a band saw, a series of sections were removed and the resdiual mounting piece then bolted to the motor mounting studs to better visualize the spatial orientation.
 



Picture DSC05348 showing bottom (left) and top (right) views of the BMW driver side motor mounts.



Picture DSC05349 showing the leading side view (left) and trailing rear view (right) of the BMW driver side motor mounts.


Picture DSC05386 showing the sectioned views of the BMW driver side motor mount during trial fittings.



Picture DSC05393 showing the final sectioned BMW driver side (left) motor mount bolted to the driver side mounting.  The steering column is to the upper left.



Picture DSC05388 showing the second sectioned BMW driver side motor mount bolted to the passenger side (right) motor mount.


Picture DSC05398 showing the top view of both motor mounts bolted to place on the engine mounts.  Note the lack of symmetry.  The actual distance between the mounting brackets and the sides of the Warp 11 are essentially the same.  The apparent difference is due to the camera angle.

The next task will be to weld mounting plates to the face of each sectioned motor mount.  Finally, a clam-shell design circumferential clamp will be made that can be bolted to both the motor and to the welded plates on the sectioned engine mounts.  Generation 2 motor mounts will be made from scratch as symmetrical castings with mounting points pre-drilled and ready for attachment to a clam shell designed circumferential clamp.

Thursday, January 31, 2013

1992 BMW 325i Crankcase Position/RPM sensor 2.0

The intention is to install the BMW harmonic damper, recovered from the M50 engine, onto the Warp 11 shaft.  The CPS (crankcase position sensor) will then be mounted in close proximity to the teeth of the damper.  During shaft rotation, the iron teeth of the damper will cause a change in the magnetic field within the Aluminum clad sensor and the wire coil within the CPS will generate an AC output signal.  With luck, the generated signal will directly drive the rpm gauge in the existing instrument cluster.  The additional benefit of this idea, is the availability of the integral pulley wheel that can be used to power accessories as needed. 

The machine shop fabricated a sleeve on the lathe that would serve as a spacer between the existing shaft (7/8” in the older style Warp 11 being used), and the 32 mm ID inner opening of the BMW harmonic damper hub.  The shop also produced a spacer (Picture DSC05315) that is about 0.0605” thick x 1.1330” ID x 1.2577” OD, and it can be used with the newer version Warp 11 motors produced after 7/1/2012.  The thicker sleeve was produced on a lathe and the key way was cut with a mill, while the thinner sleeve was rolled from galvanized steel plate.  I will have some extra adapters made and they will be available to other EVers upon request.
 
 
 
 
Picture IMG6595 of adapter sleeve used to connect the 0.875" shaft of the Warp 11 to the BMW damper hub whose ID was 32 mm.  Final dimensions of the sleeve were: 0.878 ID x 1.258" OD x 1.375 Long.



Picture DSC05315 showing the rolled adapter used to connect a 1.125" diameter Warp 11 shaft to the BMW damper hub whose ID was 32 mm. Final dimensions were about 1.1330 ID x 1.2577 OD x 1.3900 Long. This adapter has some flex during installation. 
  
 
 
 
Picture DSC05306 showing 7/8” drive shaft, machined sleeve (0.878” ID x 1.258” OD x 1.375" Long), and a 3/16” key, fully inserted and engaging both the 32 mm (1.260“) harmonic damper hub key way and the motor shaft key way.  The key way on this sleeve was over sized at 0.250" and future sleeves will have a key way slot of 0.1875" to better match the 0.1875" key.  The installed key dimensions were 0.400” x 0.1875” x 1.2502 and it was cut using a band saw from steel plate that was 3/16” x 1.25” x 6” (McMaster Carr).


 
Picture DSC05309 showing the 58 tooth damper bolted to the damper hub, and secured to the 0.875” Warp 11 commutator end shaft.



Picture DSC05310 showing oblique view of the installed harmonic damper.

 
The CPS will be mounted on an accessories end plate (currently under fabrication) and it will be in close proximity to the 58 teeth of the damper.  An Aluminum set screw shaft collar (picture DSC05317, McMaster Carr part 9946K22) was mounted on the shaft in direct contact with the motor bearing and the damper hub.  This collar fixes the dimension between the motor bearing and the damper hub. 
 

 
Picture DSC05311 showing a close up side view of the installed harmonic damper.  Note that there is sufficient room for a 0.625” (15.875 mm) Aluminum accessories end plate to be mounted on the end cap of the Warp 11.
 
 

 
Picture DSC05317  showing the set screw shaft collar prior to installation between the damper hub and the motor bearing.

Monday, January 21, 2013

Energized test of the drive train !!

(Updated 1/22/2013 to include photos)

The Warp 11 and Getrag transmission were bolted together on the bench and the rear transmission cross member attached to the transmission prior to lowering the assembly into the motor compartment with a chain hoist. The front of the Warp 11 rested on the car frame with the rear of the transmission being supported with a floor jack.


Picture 05218 showing the lowering of the Warp 11/Getrag into the motor compartment.


Using a rolling floor jack, the weight of the transmission was supported and the assembly moved toward the back of the car. Four replacement mounting bolts (obtained from Patrick BMW, $8.00) were used to attach the cross member to the undercarriage of the car. The drive shaft was then installed, first attaching the four bolts at the rear differential joint, followed by attachment of the center support bearing. The bolt heads of the flex joint would not clear the rear transmission cross member, so the rear transmission cross member bolts were removed from one side, and loosened on the other. This provided enough clearance for the flex joint to wiggle into the space and mate to the transmission flange. Luckily, the red paint marks previously painted on the drive shaft, transmission flange, and differential flange, were all intact, so it was possible to realign all the components without difficulty.


Picture 05302 showing the undercarriage view of the installed drive train and drive shaft. The rear transmission cross member was previously sand blasted and repainted prior to attaching it with new mounting bolts.




Picture DSC05213 showing the empty motor compartment with the ICE engine mounting brackets in place.




Picture DSC05297 showing the position of the left hand ICE mounting bracket after the Warp 11 had been secured to the drive shaft and differential. The bracket will provide some dimensional information, but it is not usable in its current form without significant modification and welding.




Picture DSC05303 showing the available space in the motor compartment after the Warp 11 had been secured to the drive shaft and differential.


THE WHEELS TURN !!!!



Video MOV05299 showing the operation of the temporary trunk located on/off switch, the rotation of the rear wheels, and a view of the operating motor in the motor compartment.

 

Monday, December 31, 2012

1992 BMW 325i Crankcase Position/RPM Sensor 1.0


Several EV sources offer rpm sensors that can be mounted on the Warp 11.  Some of the sensors provide a 2, 3, or 4 pulse output per motor revolution.  By contrast, the BMW rpm sensor provides 58 pulses per revolution.  It may be possible to mount the original vibration damper directly on the Warp 11 motor shaft.  This would provide the original 58 pulses per revolution which might then interface directly to the BMW instrument cluster and/or the ecu without the use of an adapter.  Additionally, the damper incorporates two pulley wheels.  One pulley can be removed, but the second is welded to the damper itself and it would be perfect for the future incorporation of belt driven accessories.


Picture DSC05255 showing original 58 tooth vibration damper.  The crankcase position/rpm sensor is at 11:00.  Removal of the plastic end caps on each pulley exposed the attachment bolts.  Picture was taken after the removal of the six hub bolts and the auxiliary second pulley.

 
Removing the vibration damper (also called by some the harmonic damper) did not disappoint in the challenge.  The primary difficulty was to immobilize the M50 camshaft  to prevent engine rotation while the 22 mm hex bolt was loosened.  Since the engine was on its side in the shop, the oil pan was removed to expose the cam shaft.  A piece of wood was inserted adjacent to the cam shaft to prevent its rotation but still, the bolt held fast. 
 
 
Picture DSC05263 showing the insertion of a wooden block to prevent rotation of the camshaft during the removal of the 22 mm retaining bolt. 

 
Subsequent use of an oxy-acetylene torch to heat the hex bolt and adjacent donut shaped washer to nearly red heat, resulted in the easy removal of the bolt.  It was necessary to remove some adjacent pulleys (bolts hiding behind the plastic end caps !!) before the damper would slide off the 32.0 mm OD cam shaft. 
 
 
 Picture DSC05262 showing the removal of the 22 mm retaining bolt with its adjacent "donut shaped" spacer/washer.
 
The primary pulley appears to be welded to the damper and six M8 x 18 bolts attach the outer pulley (D=122 mm) to the damper.  Only five bolts came out without protest, and the sixth sheared in half, so additional effort will be required to remove the remaining bolt threads.

To see an excellent exploded view diagram of the parts involved, go to realoem.com and in the search field "Part NR Application Search" enter part number 11231730311, followed by selecting "Details for E36", then, select the "Belt Drive-Vibration Damper" tab in the "E36 325i Sedan, M50, Manual" category.   From the diagram, replacement of hub part number 06 with a new hub whose ID is consistent with the Warp 11 motor shaft diameter, should allow the damper to directly mount to the Warp 11 motor.

The 3.93 kg vibration damper is a 60 tooth disk which has two teeth removed.  When rotating, the 58 remaining teeth pass within 1 mm of the crankshaft position sensor/rpm sensor (CPS).  The engine mounted CPS was damaged during attempted removal, so an EBay replacement was purchased from carpartswholesale for $24.25  .


Picture DSC05267 showing the mesial face (closest to the engine) of the vibration damper (note the sheared bolt at 4:00 !!)



Picture DSC05268 showing the distal face (closest to the radiator) with integral pulley.




Picture DSC05272 showing the side view of the 3.93 kg vibration damper.  The outer pulley has already been removed.  Using a lathe, it may be possible to thin the metal disk adjacent to the teeth to reduce the weight of the damper if desired. The integral attached pulley may allow the future incorporation of belt driven accessories.

Thursday, December 27, 2012

1992 BMW 325i Instrument Cluster 1.0

Picked up a spare BMW 325i Instrument Cluster including the three attached male plugs and 4 inch wire leads from a local salvage yard to learn more about how it can be interfaced to the EV.  The donor was from vin # BABF4319PEK09282 which according to Mitsuhiko’s BMW VIN Decoder (http://www.bmw-z1.com/VIN/VINdecode-e.cgi ) was a 1993/06 BMW 325is E36 M50 Coupe with automatic transmission.  To facilitate the testing, each of the cable wires were terminated into plastic terminal blocks (McMaster Carr part #  7618K618) that were bolted to acrylic and labeled with both wire color and function.

 
                                                                  Picture DSC05248
Showing the fully wired instrument cluster attached to terminal strips.
 
 
 
                                                                 
                                                                    Picture DSC05249
Showing the labelled terminals and the individual wires that originated from the three sockets on the back of the instrument cluster.  Wire color description on the top, and function on the bottom.


Study of the backside of the cluster and comparison with the wiring diagram printed in the Bentley BMW 3 Series Service Manual determined the following:

(1)  There are three plugs that connect the cluster to the wiring harness.  A white Siemens 26 pin part # B0126-S501 (described as CONN A in Bentley), a blue Siemens part # B1026-S502 26 pin plug (described as CONN B in Bentley), and a black AMP 12 pin part # 1-963003-2 BMW1383712 PBTP plug (described as CONN C in Bentley).
(2) Pin 3 of CONN B is the chassis ground
(3) Pin 2 of CONN A is wired to three 3 watt illumination bulbs that provide back lighting of the instrument cluster.

One of the bulbs was burned out and it was sourced at Patrick BMW dealership and replaced.  Note that the 3 watt glass bulbs used for back lighting (second from left in picture) actually plug into a green socket (far left).  The green plug assembly could be removed from the back of the instrument cluster after rotating a quarter turn.

 
                                                                 Picture DSC05239
Showing the two types of bulbs that can be replaced from behind the instrument cluster.  The larger 3 watt back lighting bulbs (left side) are two pieces, while the smaller bulbs on the right appear to be a single unit.

After connecting the negative terminal (ground) of the 12 volt battery to CONN B pin 3 and then a jumper from CONN A pin 2 to the positive of the 12 Volt battery, the back lighting of the instrument cluster was illuminated !!  Each of the indicator and warning bulbs will be tested later.

 
                                                                 Picture DSC05253
Showing the back lighted instrument cluster after connecting 12 volts to CONN A pin 2 and ground to CONN B pin 3.
 
The coding plug was not included with the instrument cluster as obtained from the salvage yard and consequently the original mileage and service status lines at the bottom of the cluster can not be illuminated.  

It is intended that the 1992 BMW 325i’s EV build will retain the original ECU and the CAN bus.  The speedometer appears to be actuated from a signal produced by the vehicle speed sensor located on the differential.  The ICE gas gauge signal was produced by a pair of variable resistors wired in series as an integral part of the floats in the original ICE gas tank.  Replacement of these variable resistors with a new circuit might simulate a measurement of residual battery pack capacity.  It may be possible to replace the engine/radiator temperature gauge sensor with a thermocouple or equivalent device whose temperature range and performance corresponds to the approved temperature range of the Warp 11.

The original ICE RPM gauge obtained its signal from the crank position sensor (CPS), also referred to in Bentley as the Front Harmonic Balancer, or the Vibration Damper.  (A good drawing can be downloaded from the following link from realoem.com  


Builder’s Note:  The web page located at realoem.com is a tremendous resource of both BMW exploded view diagrams and BMW part numbers. 

If the vibration sensor, its mounting hub, and the crankshaft position sensor are removed from the original M50 engine and the parts mounted at the commutator end of the Warp 11, it should be possible to directly activate the tachometer when the Warp 11 is rotating. 

It may not be possible to incorporate the MPG gauge at the bottom of the RPM readout, but it would be a great if it could provide a measurement of watts per mile or equivalent measurement of energy efficiency.
 
From study of the wiring diagrams in Bentley it was possible to print an excel file that was then cut out and attached to the underside of the acrylic mounting plastic.  The descriptions listed below will be edited and updated as more is learned about the wiring of the circuits.  Readers are very welcome to contribute any information that they are willing to share about different ways that the BMW instrument cluster can be rewired for EV application. 

Wire Color
 
Conn
Description
 
 
 
 
Brn/Org
 
 A24
 
Grn/Vio
 
 A23
 
Red/Yel
 
 A22
 
Wht/Blk
 
 A21
Eng Control Sys
Blk
 
 A20
Eng Control Sys
Yel
 
 A19
 
Brn/Vio
 
 A18
Brake Fluid Ind
Brn/Grn
 
 A17
Park Brake Ind
Gry
 
 A16
Check Eng Light
Vio
 
 A15
 
Blu/Blk
 
 A14
Supp Restraint Sys
Wht/Vio
 
 A12
Data Link Conn
Wht/Yel
 
 A11
Data Link Conn
Gry/Brn
 
 A5
Transmission
Blu/Grn
 
 A4
Left Turn Ind
Blu/Brn
 
 A3
Right Turn Ind
Gry/Red
 
 A2
Interior Lights (3)
White
 
 A1
High Beam Ind
Brn/Gry/Yel
 
 B23
 
Blu/Blk
 
 B22
 
Brn/Grn
 
 B19
Oil Ind
Brn/Vio
 
 B18
 
Brn/Yel
 
 B17
 
Vio/Yel
 
 B16
 
Wht/Grn
 
 B15
 
Blu/Vio/Yel
 
 B14
 
Gry/Blk/Yel
 
 B11
ABS Ind
Wht/Gry
 
 B10
 
Blk/Red
 
 B9
 
Yel/Brn
 
 B8
Front Fog Lt Ind
Blu
 
 B6
Start/Charging
Grn
 
 B5
Charge Ind
Grn/Blu
 
 B4
 
Brn
 
 B3
 Ground
Blk/Wht
 
 B2
 
Wht/Red
 
 B1
Exterior Lights Sys
Blu/Vio/Wht
 
 B24
 
Blu/Brn/Yel
 
 B26
 
Brn/Yel
 
 C1
 
Brn/Blk
 
 C3
Vehicle Ground
Brn/Red
 
 C4
Hazard Ind